Search for: All records

Solid‐state welding of Al 1043 sheets is achieved via high‐pressure torsion (HPT) processing to produce bulk nanostructured Al disks. A homogeneous nanostructure without segregation is observed, with grain sizes of ≈430–470 nm. Miniature tensile testing, coupled with the digital image correlation (DIC) technique, is employed to determine the room‐temperature tensile deformation behavior, particularly the nonuniform behavior with necking, of the HPT‐bonded ultrafine‐grained (UFG) aluminum, comparing it with annealed coarse‐grained counterpart. The HPT‐bonded UFG Al exhibits a large fraction of post‐necking strain, which is supported by the estimated high strain rate sensitivity value ofm = 0.085, suggesting the delay of local necking leading to tensile fracture. Detailed DIC analysis reveals prolonged diffuse necking, thus delaying local necking, in the HPT‐bonded UFG Al, while the annealed samples show high fractions of local necking during the nonuniform deformation. Moreover, the DIC data illustrate that local necking predominantly occurred at a limited neck zone, maintaining a plateau strain distribution at the out‐of‐neck zone throughout necking deformation toward tensile failure for both annealed and UFG aluminum. The DIC method offers an alternative means to demonstrate the transition in necking behaviors of materials by estimating the plastic lateral contraction exponent. 

It is known that the grain size plays a major role in the mechanical properties of magnesium. The aim of the present study is to evaluate its role in long‐term corrosion rate. Samples of pure magnesium with grain sizes in the range of 0.9–82 μm are produced through severe plastic deformation and annealing treatments. The mechanical properties are evaluated using tensile tests and the corrosion behavior is evaluated using immersion tests in Hank's solution. A maximum yield stress of ≈150 MPa is observed in the sample with 1.8 μm of grain size and an elongation larger than 25% is observed in the ultrafine‐grained sample. Ultrafine‐ and fine‐grained magnesium display uniform corrosion with a decreasing corrosion rate while coarse‐grained magnesium displays localized corrosion with an accelerated corrosion rate. A corrosion rate of ≈0.2 mm year⁻¹is observed in the ultrafine‐ and fine‐grained magnesium. The corrosion product layer of the fine‐grained magnesium contains elements absorbed from the media. An analysis of the data in the literature suggests that grain refinement changes the corrosion type from localized to uniform corrosion. The exact relationship between grain size and the corrosion rate remains elusive. 

Increasing sample dimensions in high‐pressure torsion (HPT) processing affects load and torque requirements, deformation distribution, and heating. Finite‐element modeling (FEM) and experiments are used to investigate the effect of technical parameters on the scaling up of HPT. Simulations confirm that axial load and torque requirements are proportional to the square and the cube of the sample radius, respectively. The temperature rise also displays a pronounced dependency on the radius. Decreasing the diameter‐to‐thickness ratio can cause heterogeneity in strain distribution along the thickness direction at the edges of the sample. Such heterogeneity is governed by friction conditions between the material and the lateral wall of the anvil depression. Simulation of HPT processing of ring‐shaped samples shows that it is possible to reach more homogeneous distribution of strain and flow stress in the processed material. Experiments using magnesium confirm a tendency for strain localization in the early stage of HPT processing but increasing the number of turns increases the homogeneity of the material. The embodied energy in HPT processing is discussed. 

The cold angular rolling process (CARP) is being developed as a continuous severe plastic deformation technique, which can process metal sheets without any length limitations at room temperature. CARP contains cold rolling and equal‐channel angular process components. The sheet thickness is kept consistent before and after CARP, allowing multiple passes of the sheet. The desired microstructure and mechanical properties can be achieved in the processed metallic sheets. The current study is aimed to evaluate the capability of CARP by processing copper sheets with different sheet widths for repetitive passes. The CARP‐treated sheets are examined by lab‐scale X‐ray and high‐energy synchrotron X‐ray diffraction to investigate the evolution in dislocation density, texture, and strain anisotropy, and by tensile testing to identify the bulk mechanical properties. The digital image correlation method is applied to tensile testing so that strain localization within the sample gauge is visualized and deformation behavior is evaluated after yielding till postnecking by estimating the hardening exponent and strain hardening rate of the CARP‐treated sheet. Comparing the reported continuous and multiple‐step processes on Cu and its alloys, the present study confirms that the CARP is potentially a useful sheet process for strengthening ductile metals.